Willett™ Pump

Willett™ Pump Positive Displacement Pump

The Willett™ Pump is a vertical, single acting positive displacement ram pump, which is designed for long life, low maintenance and optimum energy efficiency. It is the most cost-effective solution available on the market to pump difficult and abrasive sludge and slurries.

Overview

New and refurbished pumps are available to suit your requirements and budget with revised designs to meet the changing needs of today's market. It also comes with the total backing of a rapid response service from a highly-qualified team of engineers available around-the-clock.

    Unique Features

    • Pump Body
      The pump body is a strong one-piece casting manufactured from close grained cast iron. It can also be made from cast stainless steel or coated internally with a suitable material, typically rubber, nylon or polyurethane.

     

    • Rams
      Pump rams are manufactured from ceramic, Alumina or from steel coated with a high temperature ceramic. These materials are resistant to abrasion and are hard wearing. The ram is sealed by low maintenance, auto-adjusting chevron seals. Other arrangements include traditional packed glands; high specification and flushed seals are also available.
    • Ball Valves
      Attached to the body casting are the suction and discharge non-return ball valves. They have generous clearances to allow the passage of rag and large solids. Biased flow in the valve chamber rotates the ball which ensures that the ball and seat wear evenly and helps to prevent blockage. Access into the ball valve is via an easily removable cover.

     

    • Variable Speed Control
      The standard Willett pump is designed to maintain full flow over a range of operating pressures. However the pump can be equipped for variable flow. Turndown ratio varies with the pumped fluid. Control is via PLC keypad or remote MCC.

    Unique Benefits

    • Electronic Control Systems
      Reciprocation of the Willett pump ram is controlled by a PLC interacting with proximity switches and a solenoid operated hydraulic directional control valve. Where more complex control is required, a linear transducer can be fitted.

     

    • Volume Totaliser / Flow Meter
      The Willett pump displaces a fixed volume of fluid for every stroke of the pump ram. By counting the number of strokes of the pump a running total of pumped media can be given.

     

    • Blocked Pipe Detection
      Should a blockage occur in the delivery pipework then the Willett pump automatically stalls via the hydraulic system. This is detected by the PLC and a volt free contact is opened which can be used to raise an alarm and/or initiate shutdown.
    • Sludge Density Monitoring
      This patented PLC system monitors pressure differences in the delivery pipeline caused by variations in sludge density and viscosity. The pump hydraulic pressure equal to the minimum sludge density required is used as a set point. The Willett is then controlled so that it only pumps against a delivery line pressure, which is at or above the set point.

     

    • In-line Chemical Dosing
      A separate chemical injection cylinder actuated and controlled by the pump hydraulic system is used to inject polyelectrolyte or other chemical directly into the pump suction ball valve chamber. This ensures good mixing and accurate control of the chemical dose.

    Applications

    Simplex pumps will give flow rate up to 2100 litres / min (~555 gmp). Larger rates are achieved by multiple (manifolded) units operating with electronic sequencing, giving controlled constant flow output.

     

    The multiple pumps operate with a single hydraulic power pack and may optionally include an integrated stand-by power pack for economy and continuance of operation.

     

    Model No. Pump Size Flow Pressure Electrical
        m3/hr gpm bar psi kW HP
    6/75/40B 6 9.2 41 5 75 4 5
    6/150/40B 6 9.2 41 10 150 5.5 7.5
    6/300/40B 6 9.2 41 20 300 11 15
                   
    9/75/40B 9 22.5 99 5 75 11 15
    9/150/40B 9 22.5 99 10 150 18.5 25
    9/235/40B 9 22.5 99 16 235 30 40
    9/300/40B 9 22.5 99 20 300 37 50
                   
    30/35/05 30 31.8 140 5 75 11 15
    30/35/10 30 31.8 140 10 150 18.5 25
    30/35/16 30 31.8 140 16 235 30 40
    30/35/20 30 31.8 140 20 300 37 50
                   
    35/35/05 35 48 211 5 75 15 20
    35/35/10 35 48 211 10 150 22 30
    35/35/16 35 48 211 16 235 37 50
    35/35/20 35 48 211 20 300 45 60
                   
    40/75/05 40 75 330 5 75 22 3
    40/75/10 40 75 330 10 150 45 60
    40/75/16 40 75 330 16 235 75 125
    40/75/20 40 75 330 20 300 90 150
                   
    50/110/05 50 108 475.5 5 75 30 40
    50/110/10 50 108 475.5 10 150 55 75
    50/110/16 50 108 475.5 16 235 90 125
    50/110/20 50 108 475.5 20 300 110 150
                   
    50/128/12 50 126 555 12 176 90 125


    All data are based upon water at 20 deg C. Pumps are available for higher pressures and flow rates. As part of our policy for continual development we reserve the right to amend the specification without notice. Pumps fitted with chemical dosing cylinders require larger motors. For intermediate pumps sizes, please contact us.